← Back to portfolio

Sunny

Gallery

DESIGN OF JUMPSUIT

Textile elastic bands are sewn into the jumpsuit, so it sits on the body like a glove: tight and at the same time suitable for almost any body size (within reason). Cushioning zones give a large margin at the waist and unload the fur from heavy loads. The digitigrade's shape is created by a light exoskeleton linings filled synthetic winterizer. It removable Velcro lining, i.e. the linings can be washed separately. Our construction is much lighter than exoskeleton pads from foam rubber, it compresses perfectly during storage and transportation. The collar of the jumpsuit is sheathed with fleece - the suit keeps perfectly on the shoulders and does not try to fall anywhere. The zipper has a double fastening to the fur (a pair of longitudinal seams) and is well hidden. This is achieved by hemming the edges of the fur inward. All free edges of a fur are hemmed, which protects the edges from unraveling of a fabric base. To prevent the sleeves from slipping when the arms are raised, cuffs are sewn on them. Accordingly, between the overalls and the paws, the "luminous" hands of the fursuiter are not visible. Furpaws coats are sewn with a certain margin in length. Cushioning zones are formed by sewing in an elastic band, so that our fursuit fits snugly, like a glove and is universal for fursuiters of different sizes and width. Thus, you can not be afraid to gain weight or lose weight, because the suit will always fit you. No need to be afraid of size reduction due to washing - our suits have a large margin of width and height. Our fur suits allow you to wear it, for example, on a friend who is much taller and wider than you, or vice versa, lower and thinner - the suit will fit perfectly and will bring a lot of pleasure not only to you. The knots of textile elastic bands are glued with fleece so that over time these knots do not untie.

HEAD'S DESIGN

The base of the head is made of dense polyethylene foam 1/4 inch (~1 cm) thick, with a steel, stainless wire frame (see section «» on our website). Unlike a mask made of foam rubber, our design has a smaller contact area with the head of the fursuiter, it is less hot inside, this material does not rot, does not absorb moisture. Next the photos of head with the hairstyle and without this (hairstyle is removable). The project also has the couple of heads - The fursuit head consists of several parts with internal pads of different sizes for different fursuit head sizes. The mask touches the fursuiter's head at several points, so sweat is not absorbed into the mask as intensively as in foam constructions. The material of the mask does not absorb moisture at all! The mask is completely washable. The jaw can be easily removed completely, which is convenient for quick drying and cleaning. The fastening is reliable and simple, and no any bolts, nothing for lose. There is enough space in the mask for goggles. The apron consists of two halves: the front (under the jaw) and the back (actually - the head itself). They are attached to each other with buttons. There are a couple of pockets on the aprons - for USB power supply of the fan mainly. You can keep the jaw on the place, but fully open to 180 degrees for quick drying. The follow eyes are made of sheet white plastic. The transparent part is printed on a perforated banner and raised (tinted) with acrylic. "Eye boxes" do not have sharp corners in visible places, so the joints are not visible (they are hidden in the corners of the eyes). The nose is not so soft bc made of the ruber and covered with fleece. The teeth (as well as the lips) are made of fleece: - upper teeth - removable, with Velcro; - the lower teeth are glued to the jaw (remember that jaw can be easily removed from the mask for washing). There is a removable fan with a built-in converter from 5 to 12 volts, i.e. Power is provided from any USB - power bank, which fits into an apron pocket. The fan is held in place by using velcro. When the FUN is in his place, the mouth of the mask stays ajar and your jaw can rest from having to be constantly open for free breathing. The head of the fursuit is perfectly ventilated through large holes in the ears - it is can cooler inside the mask than without it when the fan is there.

TAIL'S DESIGN

The tail has the removable fur skin for more convenient washing. A very strong mount is attached to the base of the tail, from a textile tape, under a regular belt. The overalls have the sleeve of fur was made for a smooth transition for the tail. This is so that the tail does not look like a separate hanging piece. It is better to insert the tail into this sleeve in advance before putting on the jumpsuit.

PAWS DESIGN

On the paws there are soft fleece claws filled with padding synthetic winterizer. Paw pads are dense and voluminous. Comes with sandals with rubber soles. The paws are made as right/left, this makes walking a little easier. Inside the paws is a fleece sock that can be turned outside for quick drying or cleaning. The hand paws are fifth-fingere. The fifth finger can be used, it not sewn up. To make the fingers look plump and not dangle in the hand, the inside of each finger has its own soft lining. Fleece bobs are densely filled with padding polyester. So, the end now :) Or about fursuit's dimensions - it's below.

Dimensions

Not sure how to measure? How to measure