Jumpsuit design |
||||
|
The jumpsuit have
tied by textile elastic bands, thus it fits on a body as glove - tight
and at the same time it and fits almost every size of body. Multi-size
fursuit makes it easier to sell it, if you don't need it anymore.
Depreciation zones are made by sewing in a rubber band - our fursuits
has big reserve at the waist and 20" for heights reserve (regarding the
growth 5'3").
The "digitigrade's character" shape sets by a light linings, that
filled by a synthetic winterizer and make as removable by Velcro.
Linings can be washed separately. Our design from light lining are much
lighter than pads from foam rubber - it perfectly compressed during
storage and transportation, and it not are tire when the suit are
wearing.
|
||||
|
||||
| The zip has a double fastening (seam) to the fur and has a good hidden - this is achieved by stitching the edges of the fur to inside. | ||||
 |
||||
 |
||||
|
All the fur's free
edges are hemmed and don't stick out, this is protects the fur's
fabric base.
 |
||||
| The arms has the cuffed to prevent slipping of the sleeves when the arms are raised up. Accordingly, the "luminous" hands of the fursuiter are not visible between the jumpsuit and handpaws. | ||||
 |
||||
|
The cushioning zones
are made by sewing in an elastic band - our fursuit fits like a glove
and universal for any-size of fursuiters.
You can not be afraid to get fat or lose weight - the costume will always good fit you. You may not be afraid of reducing the size by the washings - our costumes have a large supply of width and height. Our fursuits allows to dress it on friend, which is much higher and wider than you, or vice versa, lower and thinner - a costume will be fit perfectly and will give a lot of fun not only to you. Or this allows sell fursuit quicker, as it is suitable for anyone. The knots of the elastic are pasted over with fleece so that the knots do not loosen over time. |
||||
 |
||||
Head design |
||||
|
The head was made of
½ inch polyethylene foam with a steel wire frame (see "BUILD
EXAMPLES" on our site). In contrast to the mask from foam rubber, our
design has a smaller area of contact with the head of the fursuiter -
it is less hot inside, the material does not rot, does not absorb
water.
|
||||
 |
||||
 |
||||
 |
||||
 |
||||
|
The fursuit head
consists of several parts with linings different sizes for different
head sizes. The mask touches the fursuiter head at several points, so
sweat is not
absorbed into the mask, as in foam structures. The jaw is completely
removable- it is convenient for quick drying and cleaning. There is
enough space in the mask for wearing glasses.
|
||||
 |
||||
|
The eyes are made of
thick white plastic and drawn with acrylic (mask full washeble). We
paint eyes with acrylic on the banner mesh. The "boxes of eyes" do not
have sharp corners, so the joints are not visible. Eyes is pasted over
with white fleece from the side of the eyelid - the more reflected
light, the whiter and lighter the recessed, following (to the best of
its ability) cartoon eye.
|
||||
 |
||||
|
The fursuit's head
is well ventilated through the large holes in the ears.
|
||||
 |
||||
|
Included, big 80mm
(3") fan, removable on Velcro, in grilles on both sides. The 12 volt
fan has a 5 volt to 12 volt adapter built into the wire, therefore
powered by USB-powerbank.
|
||||
 |
||||
|
The nose is 3D
printed and covered with fleece - a little soft and the color we want.
Nose glued along the edge to the mask and sewn with an additional
thread to the mask like a button.
|
||||
 |
||||
|
The teeth and lips
made from fleece:
- upper teeth made of fleece and removable with Velcro; - lower teeth glued to the jaw. |
||||
 |
||||
|
A couple tongue,
with
Velcro.
|
||||
 |
||||
 |
||||
|
The apron consists
of two halves: front and back. It attached to each other with buttons.
A couple of large pockets for USB-powerbank, etc. are made on the
aprons.
|
||||
 |
||||
 |
||||
Tail design |
||||
|
Detachable tail
skinn for easy washing. Fastening from a strong tape for a usual belt.
For the tail in the overalls is made a “sleeve”
from fur, so that the tail does not look like a separate, hanging piece.
|
||||
 |
||||
 |
||||
 |
||||
Paws design |
||||
|
Paws have soft claws
made from fleece. Here flat the paw pads, so as not to interfere with a
long walk and not quickly wear out. Have the sandals with rubber sole.
Inside the paws there is a fleece sock, which can be turned out for
quick drying or cleaning.
|
||||
 |
||||
 |
||||
|
Fleece sock inside.
It can be turned out so that the whole structure dries faster.
|
||||
 |
||||
|
Asymmetrically
lining of the sneaker inside the base - the plump sneakers stick out to
the sides, making it easier "run" for the owner. The same lining does
not allow the sneaker to dangle. Also, feetpaws base have the heel made
from porous rubber - the heel will not be loaded and you can to walk
without fatigue for much longer.
Sandals are made of porous rubber. If from a sports mat, then in two layers. As practice shows, it is a convenient and not difficult thing to assemble. |
||||
 |
||||
 |
||||
|
Handpaws
four-fingered. On the paws voluminous pads and claws made of fleece.
The inside of the fingers is padded to keep the fingers looking plump and not loose on hand. |
||||
 |
||||
 |
||||
 |
||||
 |
||||
| UP to the beginning |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||