FurR.CluB

Textile elastic bands are sewn into the jumpsuit, so it sits on the body like a glove - tightly, and at the same time it fits almost any size within reasonable limits. Cushioning zones give a large margin at the waist and unload the fur from heavy loads. The "finger-walking" form of suit is set by the light lining filled with padding polyester which is attached to Velcro, that is the lining can be washed separately. This design is much more long-lasting and lighter than exoskeleton pads made of foam rubber. Also it compresses perfectly for storage, transportation, and does not tire with its weight when wearing a suit, especially when you sweat.

All free edges of a fur are hemmed, which protects them from unraveling of a fabric base.

The shock-absorbing zones of the overalls are formed by sewing in an elastic band, thanks to which the fursuit tightly fits the body like a glove and becomes universal for people of different sizes. Thus, you can not be afraid to get better or lose weight - the suit will always suit you. No need to be afraid of size reduction due to washing - there is a large margin of width and height. Our fursuits allow you to wear it, for example, on a friend who is much taller and wider than you, or vice versa, lower and thinner - the suit will fit perfectly and will bring a lot of pleasure not only to you. The knots of textile elastic bands are glued with fleece so that over time these knots do not come undone.

click to enlarge...

The base of the head is made of dense 1 cm thick polyethylene foam, with a steel, stainless wire frame (see section "about manufacturing" on our website). Unlike a foam rubber mask, this design has a smaller contact area with the head of the fursuiter, it is less hot inside, this material does not rot and absolutely does not absorb moisture.

Head photoset with and without magnetic eyelids (click image for larger image).

To adjust to different head sizes the fursuit mask consists of several parts with different sized internal pads. The mask touches the fursuiter's head at several points, so moisture is not absorbed into the mask as intensively as in foam structures.

The jaw can be easily removed completely, which is convenient for quick drying and cleaning. Fastening is reliable and simple, does not contain bolts that can be lost. There is enough space in the mask to wear glasses.

You can keep open the jaw by 180 degrees for quick drying. The mask is completely washable.

The apron consists of two halves: the front (under the jaw) and the back (from the head of the costume itself). The aprons are connected to each other with the help of buttons. There are a couple of pockets on the aprons for a smartphone, USB-cans - for something that is not very voluminous.

There is the removable quiet fan with a built-in converter from 5 to 12 volts, i.e. power is provided from any small USB - power bank (which fits into an apron pocket). The fan is held in place by textile Velcro.

Included are pair of tongues with Velcro fastening.

The follow eyes are made of sheet white plastic. The transparent part is printed on a perforated banner and raised with acrylic paint. Plastic "boxes" do not have sharp corners in visible places, so the joints are not visible (it was hidden in the corners of the eyes).

The nose is soft, made of the base material of the mask and lined with fleece.

Teeth, lips, made of fleece:
- upper teeth are removable, with Velcro (pair included);
- the lower teeth are glued to the jaw and it can be easily washed after removal together with the jaw;
- a pair fangs included fasten with Velcro.

The head of the fursuit is perfectly ventilated through large holes in the ears, so it is cooler inside the mask with the fan on than without mask.

The tail is made with a removable fur skin for easier washing. A very strong fastening for a regular belt is made of nylon tape and holds on to the base of the tail, that is the skin of the tail will not tear if it is pulled.

click to enlarge...

The "sleeve" of fur for the tail in overalls - is made for a smooth transition and hiding tail attachment.

The feetpaws from foam rubber base. The heels is hidden inside so as not to beat off the heel during prolonged wear. The foot is held with soft linings on the sides and despite the large size of the feetpaws it do not hang out (up to foot length of 32cm or 13" ).
The paws have soft claws, all made of fleece and filled with padding polyester. Paw pads are voluminous.
Included with outdoor sandals from light foam rubber soles.

click to enlarge...

Inside the paws there is a fleece sock that can be turned outside for quick drying or cleaning.

The paws are four-toed. Fleece claws are filled with padding polyester. The inside of each finger has its own soft lining to make the fingers look plump, but not dangling on the hand. Fleece paw pads.