PHOTOSESSION
Fursuit was custom made. Fox and Tiger hybrid.
Jumpsuit design |
||||
The jumpsuit have
tied by textile elastic bands, thus it fits on your body as glove - tight
and at the same time it and fits almost every size of body. Multi-size
fursuit makes it easier to sell it, if you don't need it anymore.
Depreciation zones are made by sewing in a rubber band - our fursuits
has big reserve at the waist and 20" for heights reserve (regarding the
growth 5'3").
The "digitigrade's character" shape sets by a light linings, that
filled by a synthetic winterizer and it make as removable by Velcro.
Linings can be washed separately. Our design with light lining are much
lighter than pads from foam rubber - it can perfectly compressed for storage and transportation, also it not are tire when the suit are wearing.
This suit was tailored to the customer's size, therefore it has inserts to increase the length of the legs and arms. |
||||
|
||||
The zip has a double fastening (seam) to the fur and has a good hidden - this is achieved by stitching the edges of the fur to inside. | ||||
All the fur's free
edges are hemmed and don't stick out, this is protects the fur's
fabric base.
|
||||
The arms has the cuffed - this is to prevent slipping of the sleeves when the arms are raised up. And, ccordingly, between the jumpsuit and handpaws are not visible "luminous" hands of fursuiter | ||||
The cushioning zones
are made by sewing in an elastic band - our fursuit fits like a glove
and universal for any-size of fursuiters.
So, you can not be afraid to get fat or lose weight - the costume will always good fit you. You may not be afraid of reducing the size by the washings - our costumes have a large supply of width and height. Our fursuits allows to dress it on friend, which is much higher and wider than you, or vice versa, lower and thinner - a costume will be fit perfectly and will give a lot of fun not only to you. Or this allows sell fursuit quicker, as it is suitable for anyone. The knots of the elastic are pasted over with fleece so that the knots do not loosen over time. |
||||
Head design |
||||
The head was made of
½ inch polyethylene foam with a steel wire frame (see "BUILD
EXAMPLES" on our site). In contrast to the mask from foam rubber, our
design has a smaller area of contact with the head of the fursuiter, it is less hot inside, this material does not rot, does not wet absorb.
|
||||
The fursuit head
consists of several parts with linings different sizes for different
head sizes. The mask touches the fursuiter head at several points, so
sweat is not
absorbed into the mask, as in foam structures. The jaw is completely
removable- it is convenient for quick drying and cleaning. There is
enough space in the mask for wearing glasses.
|
||||
You can leave the jaw on and leave the mask to dry completely open.
|
||||
The eyes are made of thick white plastic and printed on a banner printer (mask full washeble). The "boxes of eyes" do not have sharp corners, so the joints are not visible. Eyes is pasted over with white fleece from the side of the eyelid - the more reflected light, the whiter and lighter the recessed, following (to the best of its ability) cartoon eye.
|
||||
The nose is soft and covered with fleece.
|
||||
The teeth and lips
made from fleece:
- upper teeth made of fleece and removable with Velcro; - lower teeth glued to the jaw. |
||||
There is a removable fan. The fan is held by friction in the mouth (it spreads the mouth to the sides). When the ventilator is installed, the mouth of the mask remains open (there is no need to operate the jaw at this point). Also the fursuit's head is well ventilated through the large holes in the ears.
|
||||
A set of tongue included. Sticky by Velcro.
|
||||
The apron consists
of two halves: front and back. It attached to each other with buttons.
A couple of large pockets for smartphone, USB-powerbank, etc. are made on the
aprons.
|
||||
Tail design |
||||
Detachable tail
skinn for easy washing. Fastening from a strong tape for a usual belt.
For the tail in the overalls is made a “sleeve”
from fur, so that the tail does not look like a separate, hanging piece.
|
||||
Paws design |
||||
On the paws are soft fleece claws. The paw pads are dense and voluminous. There are sandals with rubber soles. Inside the legs there is a fleece toe that can be unrolled for quick drying or cleaning.
|
||||
Fleece sock inside.
It can be turned out so that the whole structure dries faster.
|
||||
Handpaws
four-fingered. On the paws claws made of fleece.
The inside of the fingers is padded to keep the fingers looking plump and not loose on hand. |
||||
UP to the beginning |