FurR.CluB

The jumpsuit have tied by textile elastic bands, thus it fits on a body as glove - tight and at the same time it and fits almost every size of body. Multi-size fursuit makes it easier to sell it, if you don't need it anymore. Depreciation zones are made by sewing in a rubber band - our fursuits has big reserve at the waist and 20" for heights reserve (regarding the growth 5'3"). The "digitigrade's character" shape sets by a light linings, that filled by a synthetic winterizer and make as removable by Velcro. Linings can be washed separately. Our design from light lining are much lighter than pads from foam rubber - it perfectly compressed during storage and transportation, and it not are tire when the suit are wearing.

All the fur's free edges are hemmed and don't stick out, this is protects the fur's fabric base.

The cushioning zones are made by sewing in an elastic band - our fursuit fits like a glove and universal for any-size of fursuiters.
You can not be afraid to get fat or lose weight - the costume will always good fit you. You may not be afraid of reducing the size by the washings - our costumes have a large supply of width and height. Our fursuits allows to dress it on friend, which is much higher and wider than you, or vice versa, lower and thinner - a costume will be fit perfectly and will give a lot of fun not only to you. Or this allows sell fursuit quicker, as it is suitable for anyone.
The knots of the elastic are pasted over with fleece so that the knots do not loosen over time.

Click to enlarge

The head was made of ½ inch polyethylene foam with a steel wire frame (see "BUILD EXAMPLES" on our site). In contrast to the mask from foam rubber, our design has a smaller area of contact with the head of the fursuiter - it is less hot inside, the material does not rot, does not absorb water.

The fursuit head consists of several parts with linings different sizes for different head sizes. The mask touches the fursuiter head at several points, so sweat is not absorbed into the mask, as in foam structures. The jaw is completely removable- it is convenient for quick drying and cleaning. There is enough space in the mask for wearing glasses. 

The eyes are made of thick white plastic and drawn with acrylic (mask full washeble). We paint eyes with acrylic on the banner mesh. The "boxes of eyes" do not have sharp corners, so the joints are not visible. Eyes is pasted over with white fleece from the side of the eyelid - the more reflected light, the whiter and lighter the recessed, following (to the best of its ability) cartoon eye.

The fursuit's head is well ventilated through the large holes in the ears. 

Included, big 80mm (3") fan, removable on Velcro, in grilles on both sides. The 12 volt fan has a 5 volt to 12 volt adapter built into the wire, therefore powered by USB-powerbank.

The nose is 3D printed and covered with fleece - a little soft and the color we want. Nose glued along the edge to the mask and sewn with an additional thread to the mask like a button.

The teeth and lips made from fleece:
- upper teeth made of fleece and removable with Velcro;
- lower teeth glued to the jaw.

A couple tongue, with Velcro.

The apron consists of two halves: front and back. It attached to each other with buttons. A couple of large pockets for USB-powerbank, etc. are made on the aprons.

Detachable tail skinn for easy washing. Fastening from a strong tape for a usual belt. For the tail in the overalls is made a “sleeve” from fur, so that the tail does not look like a separate, hanging piece.

Click to enlarge

Paws have soft claws made from fleece. Here flat the paw pads, so as not to interfere with a long walk and not quickly wear out. Have the sandals with rubber sole. Inside the paws there is a fleece sock, which can be turned out for quick drying or cleaning. 

Click to enlarge

Fleece sock inside. It can be turned out so that the whole structure dries faster.

Asymmetrically lining of the sneaker inside the base - the plump sneakers stick out to the sides, making it easier "run" for the owner. The same lining does not allow the sneaker to dangle. Also, feetpaws base have the heel made from porous rubber - the heel will not be loaded and you can to walk without fatigue for much longer.
Sandals are made of porous rubber. If from a sports mat, then in two layers. As practice shows, it is a convenient and not difficult thing to assemble.

Handpaws four-fingered. On the paws voluminous pads and claws made of fleece.
The inside of the fingers is padded to keep the fingers looking plump and not loose on hand.