FurR.CluB

Textile elastic bands are sewn into the jumpsuit, so it sits on the body like a glove: tight and at the same time suitable for almost any body size (within reason). Cushioning zones give a large margin at the waist and unload the fur from heavy loads. The digitigrade's shape is created by a light exoskeleton linings filled synthetic winterizer. It removable Velcro lining, i.e. the linings can be washed separately. Our construction is much lighter than exoskeleton pads from foam rubber, it compresses perfectly during storage and transportation.

The zipper has a double fastening to the fur (a pair of longitudinal seams) and is well hidden. This is achieved by hemming the edges of the fur inward.

All free edges of a fur are hemmed, which protects the edges from unraveling of a fabric base.

To prevent the sleeves from slipping when the arms are raised, cuffs are sewn on them. Accordingly, between the overalls and the paws, the "luminous" hands of the fursuiter are not visible. Furpaws were made with a certain margin in length.

Cushioning zones are formed by sewing in an elastic band, so that our fursuit fits snugly, like a glove and is universal for fursuiters of different sizes and width. Thus, you can not be afraid to gain or lose weight, because the suit will always fit you. Also there is no need to be afraid of size reduction due to washing. The knots of textile elastic bands are glued with fleece so that over time these knots do not untie.

click to enlarge

The base of the head is made of dense polyethylene foam 1/4 inch (~1 cm) thick, with a steel, stainless wire frame (see section «BUILD EXAMPLES» on our website). Unlike a mask made of foam rubber, our design has a smaller contact area with the head of the fursuiter, it is less hot inside, this material does not rot, does not absorb moisture.

Photos of the head from different angles.

click to enlarge

The fursuit head consists of several parts with internal pads of different sizes for different fursuit head sizes. The mask touches the fursuiter's head at several points, so sweat is not absorbed into the mask as intensively as in foam constructions. The material of the mask does not absorb moisture at all! The mask is completely washable.

The jaw can be easily removed completely, which is convenient for quick drying and cleaning. The fastening is reliable and simple, and with no bolts, so nothing to lose. There is enough space in the mask for goggles.

The apron consists of two halves: the front (under the jaw) and the back (actually - the head itself). They are attached to each other with buttons. There are a couple of large pockets on the aprons - for usb power supply mainly.

You can keep the jaw on the place, but fully open to 180 degrees for quick drying.

The following eyes are made of sheet white plastic. The transparent part is printed on a perforated banner and raised (tinted) with acrylic. "Eye boxes" do not have sharp corners in visible places, so the joints are not visible.

The nose is made of the ruber and covered with fleece.

The teeth (as well as the lips) are made of fleece:
- upper teeth - removable, with Velcro; There are a couple of options for large fangs.
- the lower teeth are glued to the jaw (jaw can be easily removed from the mask for washing).
The mouth does not close completely when the fan is inserted.

There is a removable fan with a built-in converter from 5 to 12 volts, i.e. Power is provided from any USB - power bank, which fits into an apron pocket. The fan is held in place by using velcro. When the FUN is in his place, the mouth of the mask stays ajar and your jaw can rest from having to be constantly open for free breathing.

The head of the fursuit is perfectly ventilated through large holes in the ears - it is can cooler inside the mask than without it when the fan is there.

The tail has a removable fur skin for more convenient washing. A very strong mount is attached to the base of the tail, from a textile tape for a regular belt.

click to enlarge

For the tail in overalls, a sleeve of fur was made for a smooth transition - this is so that the tail does not look like a separate hanging piece. It is better to insert the tail into this sleeve in advance before putting on the jumpsuit.

The paws have soft fleece claws filled with synthetic insulation. The paws have rubber soles. The zipper at the back. The paws have removable inner side pads with Velcro fastenings. Are the inner removable heels. The entire sole is from Velcro, allowing you to attach your own shoes to the inside (you'll need to attach the Velcro to the shoes first).

click to enlarge

The handpaws have fifth-fingers, and they can be used. In this case a finger doesn't have its own soft lining inside because the fingers are narrowed and the fleece bobs are densely filled with padding polyester. The wrist of the glove is pulled together with an elastic band, which makes it difficult to put it on, but also prevents the glove from slipping during active movement. (For easy put on it is advisable to wear additional thin gloves for better slip).

So, the end now :) Up? Or about fursuit's dimensions - it's below.