FurR.CluB

The jumpsuit of this fursuit tied by textile elastic bands, thus it fits on your body as glove - tight and at the same time it and fits almost every size of body. Depreciation zones are made by sewing in a rubber band - our fursuits has big reserve at the waist and 20" for heights reserve (regarding the growth 5'3"). The "digitigrade's character" shape sets by a light linings, that filled by a synthetic winterizer and it make as removable by Velcro. Linings can be washed separately. Our design with light lining are much lighter than pads from foam rubber - it can perfectly compressed for storage and transportation, also it not are tire when the suit are wearing.

All the fur's free edges are hemmed and don't stick out, this is protects the fur's fabric base.

The cushioning zones are made by sewing in an elastic band - our fursuit fits like a glove and universal for any-size of fursuiters.
So, you can not be afraid to get fat or lose weight - the costume will always good fit you. You may not be afraid of reducing the size by the washings - our costumes have a large supply of width and height. Our fursuits allows to dress it on friend, which is much higher and wider than you, or vice versa, lower and thinner - a costume will be fit perfectly and will give a lot of fun not only to you. Or this allows sell fursuit quicker, as it is suitable for anyone.
The knots of the elastic are pasted over with fleece so that the knots do not loosen over time.

Click to enlarge

The head was made of ½ inch polyethylene foam with a steel wire frame (see "BUILD EXAMPLES" on our site). In contrast to the mask from foam rubber, our design has a smaller area of contact with the head of the fursuiter, it is less hot inside, this material does not rot, does not wet absorb.

Click to enlarge

The fursuit head consists of several parts with linings different sizes to adjust the mask on the owner's head. The mask touches the fursuiter head at several points, so sweat is not absorbed into the mask, as it happens in in foam head bases. The jaw is completely removable- it is convenient for quick drying and cleaning. There is enough space in the mask for wearing glasses. 

You can leave the jaw on and leave the mask to dry completely open.

The eyes are made of thick white plastic and printed on a banner printer (mask full washeble). The "boxes of eyes" do not have sharp corners, so the joints are almost not visible. Cartoon eyes made according to the scheme "follow" (to the best of its ability).

The nose is soft and covered with fleece.

The teeth and lips made from fleece:
- upper teeth made of fleece and removable with Velcro (you can not put them at all);
- lower teeth glued to the jaw.

There is the big removable fan. The fan is held by textile Velcro in the mouth. When the fun is installed, the mouth of the mask remains a little open. Also the fursuit's head is well ventilated through the large holes in the ears.

The fursuit's head is well ventilated through the large holes in the ears.

A set of tongue included. It stickly by Velcro (pictured is a pair, but there will be three tongues in the set).

The apron consists of two halves: front and back. It attached to each other with buttons. Head's aprons have the couple of large "pockets" - are made for smartphone, USB-powerbank, etc.

Tail have the removeble skinn for easy washing. Fastening from a strong tape, for a usual belt. For the tail in the overalls is made a “sleeve” from fur, so that the tail does not look like a separate, hanging piece.

Click to enlarge

On the paws are soft fleece claws. The paw pads are dense and voluminous. There are sandals with rubber soles. Inside the legs there is a fleece sock that can be unrolled for quick drying or cleaning.

Click to enlarge

Fleece sock inside. It can be turned out so that the whole structure dries faster.

Handpaws four-fingered. On the paws claws made of fleece.
The inside of the fingers is padded to keep the fingers looking plump and not loose on your hand.